Tuffy Bill of Materials
DO NOT PURCHASE ANY MATERIAL UNTIL YOU READ THIS SECTION.
LUMBER: All lumber listed as 1" is "Four quarters" stock
finished as full as possible. This will generally result in lumber 3/4" to
7/8" thick. All thicknesses under 1" are to be considered net as
are all widths. All lengths allow stock for trimming to fit. We suggest
grouping widths and lengths and re-sawing to size if a circular saw is
available. This will result in a considerable savings on the lumber. ALL
PLYWOOD must be an Exterior type. Grades of plywood are noted. All plywood
1/4" or 3/8" thick is to be three ply. All thicker plywood to be a
minimum of five ply.
CHECK ALL SIZES TO THE WORK PRIOR TO CUTTING.
Abbreviations used are: Mahog = mahogany, Sp = spruce, DF = Douglas-fir, PW =
plywood, EXT = exterior.
| ITEM |
MATERIAL |
NO. PCS. |
SIZE |
| LUMBER: |
| **Transom, Frames 1,2,3 |
Mahog, Sp, Oak |
25 bd. ft. |
Random widths & lengths |
| Keel |
Mahog, Sp, Oak |
1 |
1" x 4" x 9'6" |
| Battens |
Mahog, Sp, Oak |
2 |
1" x 3" x 7'6" |
| Battens |
Mahog, Sp, Oak |
2 |
1" x 3" x 8'6" |
| Battens |
Mahog, Sp, Oak |
2 |
1" x 3" x 9'6" |
| Chine log |
Mahog, Sp, Oak |
2 |
1" x 2" x 14' |
| Sheer Clamp |
Mahog, Sp, Oak |
4 |
1" x 5/8" x 14' |
| Skeg or Fin |
Mahog, Sp or Oak |
1 |
1" x 2" x 8' |
| Carling |
Mahog, Sp or Oak |
1 (makes 2) |
1" x 9" x 9' |
| Intermediate Deck Beam |
Mahog, Sp or Oak |
1 |
1" x 5" x 4'6' |
| Blocking for Beam |
Any scrap lumber |
1 (makes 2) |
1" x 3" x 8" |
| Strongback |
Mahog, Sp or Oak |
1 |
1" x 2" x 4' |
| Deck Battens |
Mahog, Sp or Oak |
1 (makes 2) |
1" x 2" x 7'6" |
| Motor Well Beam |
Mahog, Sp or Oak |
1 |
1" x 4" x 4' |
| Motor Well Cleats |
Mahog, Sp or Oak |
2 |
1" x1" x 1'6" |
| Coamings |
Mahog, Sp or Oak |
2 |
1" x 5" x 6' |
| Dash Beam |
Mahog, Sp or Oak |
1 |
1" x 5" x 5' |
| Cowl Beadings |
Mahog, Sp or Oak |
2 |
1" x 1" x 5' |
| Athwartship motor brace |
DF |
Bldg. Form Scrap |
2" x 4" x 2' 8" |
| Seat Uprights |
See Layout |
See text |
| Seat Cleats |
Mahog, Sp or Oak |
8 |
1" x 1" x 1'6" |
| Seat Spreaders |
Mahog, Sp or Oak |
2 |
1" x 2" x 1'6" |
| Walk Through Spreader |
Mahog, Sp or Oak |
1 |
1" x 4" x 1'6" |
| Spray Rails (optional) |
Mahog, Sp or Oak |
2 |
1" x 1" x 8' |
| PLYWOOD: |
**Stem, Breasthook,
Transom, Chine blocking,
& Transom knee |
PW, DF, EXT AB |
1 |
3/4" x 4' x 6' |
*Bottom Planking,
Motor Well Bottom |
PW, DF, EXT AB |
1 |
1/4" x 5' x 12' |
| *Side Planking |
PW, DF, EXT AB |
1 |
1/4" x 4' x 14' |
Forward Deck,
Side Deck, Cowl
Covering, Seat
Longitudinals |
PW, DF, Ext AB |
2 |
1/4" x 4' x 8' |
| Butt Blocks |
scraps 3/8" PW, DF, EXT AB |
| Motor Well Sides, Seat Bottoms, & Seat Backs |
PW, DF, EXT AB |
1 |
3/8" x 4' x 8' |
*Note: Can substitute 4 sheets of 1/4" x 4'
x 8' plywood for bottom &
side planking, & motor well bottom. Layout not shown on plans.
** These itenms are in the Frame Kit. |
|
FASTENINGS: Bronze or Hot dipped galvanized
- SCREWS: Flat head wood type
- 3/4"'#8 - 5 gross
- 1" #8 -1 gross
- 1 1/2" #8 -1 gross
- 2"#10 -1 gross
- 3"#l4 -6 only
- NAILS: Annular ring type - Bronze or Monel
- 1"#12 -3 lbs.
- 1 1/4"#12 -1/2 lb.
- CARRIAGE BOLTS: Bronze or Hot dipped galvanized
with nuts and washers
- 1/4" x 5" -5 required
GLUE: EPOXY, rescorcinol, Plastic resin glue: 1 gallon or 4.5
lbs.
|
Return
|