Search found 341 matches

by footer
Thu Jan 16, 2020 10:41 am
Forum: Power Boats
Topic: Downunder Monaco Utility
Replies: 33
Views: 11613

Re: Downunder Monaco Utility

Will sure be some great memories for the little ones. I still remember riding in a steam powered, covered launch when I was about four years old (I’m 62 now).
by footer
Thu Jan 16, 2020 10:31 am
Forum: Power Boats
Topic: Malahini from MD
Replies: 287
Views: 95548

Re: Malahini from MD

I’m sure you will be fine with it there.
by footer
Thu Jan 16, 2020 9:45 am
Forum: Power Boats
Topic: MI Malahini Build, Post Flip.
Replies: 207
Views: 73912

Re: MI Malahini Build, Post Flip.

Thanks guys. I finally got to the point in my life where I could by my own TIG, but my hands are no longer steady and my eyes strain to see through bifocals. So, it was challenging for me. To avoid warping, I welded them in place, but had to run short beads. Even at that, there were a couple of poin...
by footer
Wed Jan 15, 2020 1:51 pm
Forum: Power Boats
Topic: Malahini from MD
Replies: 287
Views: 95548

Re: Malahini from MD

I put my fuel vent up and forward on the sidewall of my motor well under the overhang. It’s highly unlikely it will get water in it.
by footer
Wed Jan 15, 2020 1:42 pm
Forum: Power Boats
Topic: Somerset, KY Gentry
Replies: 63
Views: 18444

Re: Somerset, KY Gentry

Looking fantastic. Very nice work.
by footer
Wed Jan 15, 2020 1:36 pm
Forum: Power Boats
Topic: MI Malahini Build, Post Flip.
Replies: 207
Views: 73912

Re: MI Malahini Build, Post Flip.

Cutwater
by footer
Wed Jan 15, 2020 1:35 pm
Forum: Power Boats
Topic: MI Malahini Build, Post Flip.
Replies: 207
Views: 73912

Re: MI Malahini Build, Post Flip.

Cutwater. Tack welded, ran short beads. Ground down welds smooth. Buffed out the grinds, sanded with 350 grit, then 1000 grit, then 3000 grit, then 7000 grit, then buffed with stainless polish. Still have some fine polishing to do.
Then I have to install my eye bolt.
by footer
Wed Jan 15, 2020 1:27 pm
Forum: Power Boats
Topic: MI Malahini Build, Post Flip.
Replies: 207
Views: 73912

Re: MI Malahini Build, Post Flip.

I finally got some time (after catching up on a long list of honey do’s) to work on some metal. Got my transom bands done and my cutwater.
by footer
Fri Jan 10, 2020 5:17 am
Forum: Power Boats
Topic: Building The Vera Cruise
Replies: 3072
Views: 626383

Re: Building The Vera Cruise

Looking great. It’s amazing how custom work is so time consuming. But, when your finished, it’s going to be something to be proud of. 😀👍
by footer
Fri Jan 10, 2020 5:12 am
Forum: Power Boats
Topic: Malahini from MD
Replies: 287
Views: 95548

Re: Malahini from MD

I was wondering how your windshield was coming along. Looking great.
I see you went with single seats too. I think your really going to like that. I couldn’t be happier with mine.
Keep up the good work. 😀
by footer
Thu Dec 26, 2019 8:37 am
Forum: Power Boats
Topic: Lee's Monaco utility build
Replies: 156
Views: 53993

Re: Lee's Monaco utility build

I had the same problem with my chines. The problem was always a knot or grains close to a knot. These areas are harder and more brittle and won’t bend at the same rate as a straight grain. The same holds true for scarf joints. Always try to put knots or joints in areas that are low stress. After bre...
by footer
Sun Dec 15, 2019 6:44 am
Forum: Power Boats
Topic: Aussie Belle
Replies: 587
Views: 200480

Re: Aussie Belle

Good to see her in the water. Sound good anyway.
by footer
Fri Dec 13, 2019 11:49 am
Forum: Power Boats
Topic: Florida Malahini Build
Replies: 79
Views: 22766

Re: Florida Malahini Build

The price on Rub rail Is ok, but shipping is astronomical!
So, I went down to Alro steel and bought some 1/4”x1/2” cold rolled stainless strips and I’m drilling, sanding it a bit round and polishing it. It should look ok, and be in my tax bracket
by footer
Fri Dec 13, 2019 9:48 am
Forum: Power Boats
Topic: Mist Miss - Desert Build
Replies: 77
Views: 13329

Re: Mist Miss - Desert Build

I have a heated garage here in Michigan I keep at 55 degrees. Like you I found keeping my epoxy in the house until I’m ready to use it, works the best and it’s always cured by the next day.
by footer
Fri Dec 13, 2019 9:37 am
Forum: Power Boats
Topic: Malahini from MD
Replies: 287
Views: 95548

Re: Malahini from MD

Pretty good bead and it sanded out nice.

Go to advanced search