Pee wee build in Sydney

Outboard designs up to 14'

Moderator: ttownshaw

User avatar
chubs
Posts: 124
Joined: Thu Dec 27, 2007 2:26 am
Location: Sydney, Australia
Contact:

Re: Pee wee build in Sydney

Postby chubs » Sat Oct 31, 2015 11:42 pm

Ah yes thanks a lot. 6mm it is. I share chug's concerns re glueing the frame to the skin, so I'll wait post-skinning to paint the frame. Cheers all :)

User avatar
chugalug
Posts: 1062
Joined: Sat Nov 29, 2014 5:01 pm
Location: top of mn.

Re: Pee wee build in Sydney

Postby chugalug » Sun Nov 01, 2015 3:31 am

:D would be good to coat frames with epoxy before skinnning.to help seal them.I didn't on Chug and had a blast doing it after the flip(access was limited)
Working on regular-sized Bo-Jest


"If it's not crooked,It's not mine

User avatar
hzchevy
Posts: 78
Joined: Sat Sep 25, 2010 2:24 pm
Location: Melbourne, Australia.
Contact:

Re: Pee wee build in Sydney

Postby hzchevy » Mon Nov 02, 2015 2:45 am

I used the 1/4 ply for the planking. I also did what chugalug suggested, I epoxy sealed the entire frame before planking and then painted afterwards. Your travelling well Chubs.

User avatar
mrintense
Posts: 2516
Joined: Thu Jun 10, 2010 11:22 am
Location: Austin, Texas
Contact:

Re: Pee wee build in Sydney

Postby mrintense » Mon Nov 02, 2015 6:45 am

I also sealed my frames before applying the plywood skins. I did this after the frames were assembled but before they were put on the building form. I did leave the edges unsealed because I wanted to wait to do that when I added the skins. In general, look at your assembly before moving into a new phase and think about what might be easier to do before going to that next step. However, always consider if this is the best thing to do at that time. A thinking chair and a cold one are your best friends at these times.
Carl
a.k.a. Clipper

Crafting a classically styled Vera Cruise named "Some Other Time"

Clipper's Vera Cruise Build

User avatar
chubs
Posts: 124
Joined: Thu Dec 27, 2007 2:26 am
Location: Sydney, Australia
Contact:

Re: Pee wee build in Sydney

Postby chubs » Sat Jan 09, 2016 7:10 pm

So I ended up sealing the frame with oil based enamel, "better done than perfect":
Attachments
image.jpeg

User avatar
chubs
Posts: 124
Joined: Thu Dec 27, 2007 2:26 am
Location: Sydney, Australia
Contact:

Re: Pee wee build in Sydney

Postby chubs » Sat Jan 09, 2016 7:12 pm

Then I positioned the side panel with clamps to make sure it covered all corners when bent around. Only just fit:
Attachments
image.jpeg

User avatar
chubs
Posts: 124
Joined: Thu Dec 27, 2007 2:26 am
Location: Sydney, Australia
Contact:

Re: Pee wee build in Sydney

Postby chubs » Sat Jan 09, 2016 7:14 pm

Then got screwing:
Attachments
image.jpeg

User avatar
chubs
Posts: 124
Joined: Thu Dec 27, 2007 2:26 am
Location: Sydney, Australia
Contact:

Re: Pee wee build in Sydney

Postby chubs » Sat Jan 09, 2016 7:15 pm

Trimmed the panel with my new jigsaw, still can't believe the Bosch died:
Attachments
image.jpeg

User avatar
chugalug
Posts: 1062
Joined: Sat Nov 29, 2014 5:01 pm
Location: top of mn.

Re: Pee wee build in Sydney

Postby chugalug » Sun Jan 10, 2016 6:25 am

:D Looks good.Did you coat everything with enamel?The panel don't get glued to frames ;however,they are glued to chine and shear as well as bottom battons as well as screwed on.couldn't tell by your pics if you would be gluing to bare wood or to enameled surface.
Working on regular-sized Bo-Jest


"If it's not crooked,It's not mine

User avatar
chubs
Posts: 124
Joined: Thu Dec 27, 2007 2:26 am
Location: Sydney, Australia
Contact:

Re: Pee wee build in Sydney

Postby chubs » Fri Jan 15, 2016 4:46 am

Yes chug I'd be gluing to the painted chines. Hopefully will stick as well as it would to bare wood.

User avatar
Bill Edmundson
Posts: 10443
Joined: Wed Nov 23, 2005 6:45 am
Location: Birmingham, AL, USA
Contact:

Re: Pee wee build in Sydney

Postby Bill Edmundson » Fri Jan 15, 2016 6:53 am

I glue to all frames and battens. I only screw to the sheer, chine, keel, stem, and transom.

Bill
Mini -Tug, KH Tahoe 19 & Bartender 24 - There can be no miracle recoveries without first screwing up.
Tahoe 19 Build

User avatar
chugalug
Posts: 1062
Joined: Sat Nov 29, 2014 5:01 pm
Location: top of mn.

Re: Pee wee build in Sydney

Postby chugalug » Fri Jan 15, 2016 7:48 am

:D Sorry Chubs guess I was wrong in my interpretation of Glen-L practices.I yield to the forum experts.
Working on regular-sized Bo-Jest


"If it's not crooked,It's not mine

User avatar
chubs
Posts: 124
Joined: Thu Dec 27, 2007 2:26 am
Location: Sydney, Australia
Contact:

Re: Pee wee build in Sydney

Postby chubs » Fri Jan 15, 2016 1:53 pm

Glueing has to be proper epoxy right?

User avatar
Bill Edmundson
Posts: 10443
Joined: Wed Nov 23, 2005 6:45 am
Location: Birmingham, AL, USA
Contact:

Re: Pee wee build in Sydney

Postby Bill Edmundson » Fri Jan 15, 2016 2:08 pm

I used Thixo or West Six 10. They are 2 part in a caulking cartridge. Just run a bead on the frame (etc.). Then spread it with a tongue depressor. It ain't cheap. It's a lot easier and faster than mixing it yourself, though.

Bill
Mini -Tug, KH Tahoe 19 & Bartender 24 - There can be no miracle recoveries without first screwing up.
Tahoe 19 Build

User avatar
hzchevy
Posts: 78
Joined: Sat Sep 25, 2010 2:24 pm
Location: Melbourne, Australia.
Contact:

Re: Pee wee build in Sydney

Postby hzchevy » Sun Jan 17, 2016 1:37 am

It's looking more and more like a boat every post :D
I also glued and screwed to my frames. Wasn't sure if that was right but seems to work. Although I didnt glue to paint. Not sure how that will work. It's surely coming along though. Good work.


Return to “Small outboards”

Who is online

Users browsing this forum: Yahoo [Bot] and 11 guests