Mounting Stringers to Building Form - Jackknife

Outboard designs up to 14'

Moderator: ttownshaw

AndrewS
Posts: 8
Joined: Thu Oct 13, 2016 6:41 pm

Mounting Stringers to Building Form - Jackknife

Postby AndrewS » Mon Oct 24, 2016 6:57 pm

Dear Gentlemen,

What is the best way to mount stringers to the building form?

Many thanks,
Andrew

JimmY
Posts: 509
Joined: Sat Jul 30, 2016 11:08 am
Location: Brighton, MI

Re: Mounting Stringers to Building Form - Jackknife

Postby JimmY » Tue Oct 25, 2016 9:25 am

Hi Andrew,

I'm not sure I understand your question. If you mean the sheer and chine, then these are typically epoxied and screwed to each frame. If you mean the motor stringers that will be part of the boat, then you need to make them removable (screws and/or clamps) such that you can get to them once the boat hull is framed and sheeted.

I hope this helps.
-Jim
Nothing says poor craftsmanship like wrinkles in your duct tape!

User avatar
BarnacleMike
Posts: 822
Joined: Wed Sep 21, 2011 7:47 am
Location: North Georgia / Chattanooga Area
Contact:

Re: Mounting Stringers to Building Form - Jackknife

Postby BarnacleMike » Tue Oct 25, 2016 10:13 am

Andrew,

I'm not very familiar with the Jackknife design, but from this photo

Image

it looks like the stringers help to form the supports for the floor. Take a close look at your plans & instructions. From the looks of this photo, it would almost appear that the longitudinal supports of the building form ARE the stringers.
-Michael

Built Utility "Perseverance" — completed Aug 2016
Currently building a Zip
My Boatbuilding Blog: http://barnaclemikeboats.blogspot.com/
My Website of Boat Photos: https://michaelsmaddox.wordpress.com

User avatar
chugalug
Posts: 1062
Joined: Sat Nov 29, 2014 5:01 pm
Location: top of mn.

Re: Mounting Stringers to Building Form - Jackknife

Postby chugalug » Tue Oct 25, 2016 10:18 am

:roll: Or are you talking about the boards screwed to frames at the set up level line and screwed to the build form? I fastened mine down with screws and using framing square from level build form,fastened an angled piece on each side to help hold in place. :D
Working on regular-sized Bo-Jest


"If it's not crooked,It's not mine

User avatar
Roberta
Posts: 5946
Joined: Tue Jul 31, 2007 5:23 pm
Location: East Troy, Wisconsin

Re: Mounting Stringers to Building Form - Jackknife

Postby Roberta » Tue Oct 25, 2016 10:53 am

Not real familiar with the Jackknife. It appears that it is a smaller outboard cruiser. Typically stringers are used on larger inboards for motor mounting or larger outboards. Stringers are used as a setup level for framing where the floor timbers are in some way positioned on them to set the level of the framing to ensure that the keel, chines and shears are in alignment. Stringer clips are used to fasten the framing to the stringers once the proper location and height are established. C clamps and/or Erwin clamps can be used to secure the stringers to the uprights on the build form. The temporary clamps are used until the stringers are set level both longitudinally and athwart ship. Then a drywall screw or two can be place to ensure the setup remains in place. Clamps and screws need to be placed so that they can be removed later so the hull can be removed from the form and the hull righted.

Here are some pics of my Torpedo build form with the stringers set and framing being set in place. Use diagonals and other bracing to ensure that the form is secure and stable. A large level is helpful in getting the form perfectly level from side to side, front to back, and diagonally. Use clamps when constructing the form and, when level, secure with screws.

Roberta
Attachments
build frame 002.JPG
setup 3 003.JPG
Roberta "Queen of the Boat Builders"
Built Zip "Oliver IV", Super Spartan "Jimmy 70", and Torpedo "The Glen L".

AndrewS
Posts: 8
Joined: Thu Oct 13, 2016 6:41 pm

Re: Mounting Stringers to Building Form - Jackknife

Postby AndrewS » Tue Oct 25, 2016 10:37 pm

Dear Jimmy, Chugalug, Barnacle Mike and Queen Roberta,

Thank you very much for your replies. I understand now:)

My teak arrives on Saturday!

Cheers,
Andrew


Return to “Small outboards”

Who is online

Users browsing this forum: Yahoo [Bot] and 11 guests