Transom saver with manual tilt outboard

Boat trailers and trailering

Moderator: ttownshaw

User avatar
soedesh
Posts: 136
Joined: Sun Aug 22, 2010 10:30 am
Location: Long Island, NY
Contact:

Transom saver with manual tilt outboard

Postby soedesh » Fri Sep 01, 2017 1:55 am

Hi, I have a manual tilt Mercury 650 on a Malahini and I intend to use a transom saver (it will arrive today). I was wondering if others with a similar setup trailer with the outboard fully tilted and latched, or whether the outboard is left unlatched so it rests on the transom saver.

Thanks,
Shawn

User avatar
billy c
Posts: 2079
Joined: Sun Oct 15, 2006 7:59 pm
Location: NH
Contact:

Re: Transom saver with manual tilt outboard

Postby billy c » Fri Sep 01, 2017 4:34 am

Best scenario is to just leave the motor vertical. The transom is plenty strong. If you do need to tilt for ground clearance then do not latch it as it puts undue stress on the mounting bracket.
(insert Witty phrase here)
Billy's Belle Isle website

JimmY
Posts: 500
Joined: Sat Jul 30, 2016 11:08 am
Location: Brighton, MI

Re: Transom saver with manual tilt outboard

Postby JimmY » Fri Sep 01, 2017 4:41 am

I'm no expert, but my boating expert friend ditto's Bill's comment to trailer with the motor vertical. Just make sure to tilt it when backing it down the ramp.
-Jim
Nothing says poor craftsmanship like wrinkles in your duct tape!

User avatar
Bill Edmundson
Posts: 10396
Joined: Wed Nov 23, 2005 6:45 am
Location: Birmingham, AL, USA
Contact:

Re: Transom saver with manual tilt outboard

Postby Bill Edmundson » Fri Sep 01, 2017 5:24 am

Yamaha 4 strokes say not to tow with the engine tilted. Because of the oil sump.

Bill
Mini -Tug, KH Tahoe 19 & Bartender 24 - There can be no miracle recoveries without first screwing up.
Tahoe 19 Build

gdcarpenter
Posts: 1325
Joined: Tue May 05, 2009 12:18 pm
Location: Raleigh, North Carolina

Re: Transom saver with manual tilt outboard

Postby gdcarpenter » Fri Sep 01, 2017 5:30 am

I leave the tilt latch off and use the transom saver to support the engine.
Attachments
image.jpeg
This is my first, last and only boat build.

http://www.gdzipbuild.blogspot.com

User avatar
BarnacleMike
Posts: 820
Joined: Wed Sep 21, 2011 7:47 am
Location: North Georgia / Chattanooga Area
Contact:

Re: Transom saver with manual tilt outboard

Postby BarnacleMike » Fri Sep 01, 2017 10:58 am

gdcarpenter wrote:I leave the tilt latch off and use the transom saver to support the engine.

Ditto for me, trailering with a smaller motor... an 8hp Nissan (Tohatsu)
-Michael

Built Utility "Perseverance" — completed Aug 2016
Currently building a Zip
My Boatbuilding Blog: http://barnaclemikeboats.blogspot.com/
My Website of Boat Photos: https://michaelsmaddox.wordpress.com

User avatar
vupilot
Posts: 3227
Joined: Wed Apr 15, 2009 7:36 am
Location: Indy
Contact:

Re: Transom saver with manual tilt outboard

Postby vupilot » Fri Sep 01, 2017 3:19 pm

I really love the transom saver for motors with manual tilt. It really does take a lot of weight off the transom and transfers to the trailer. I feel much better going over rough highways with it. Yes, youll see when you get it, it will be unlatched and uses a bungee to wrap around the motor leg. It is true that you might not want to use it with four strokes as the tilt can cause oil to pool in the carb or airbox.

User avatar
soedesh
Posts: 136
Joined: Sun Aug 22, 2010 10:30 am
Location: Long Island, NY
Contact:

Re: Transom saver with manual tilt outboard

Postby soedesh » Sun Sep 03, 2017 4:36 am

Thanks for the input, I will use it today without the engine latch for the maiden voyage. I do plan to rig up something so that the bottom part of the rod that goes over the roller won't come off.

Note that there is a sticker on the transom saver that says it is only to be used on motors with power tilt and trim - but what do they know! lol.

User avatar
Roberta
Posts: 5926
Joined: Tue Jul 31, 2007 5:23 pm
Location: East Troy, Wisconsin

Re: Transom saver with manual tilt outboard

Postby Roberta » Sun Sep 03, 2017 6:31 am

I drilled holes in the bottom flanges on my transom saver. Then bent a long 1/4" bolt to go around the roller and engage the holes in the flanges. A nylock nut held the bolt from slipping out.

Roberta
Roberta "Queen of the Boat Builders"
Built Zip "Oliver IV", Super Spartan "Jimmy 70", and Torpedo "The Glen L".


Return to “Trailers and trailering”

Who is online

Users browsing this forum: No registered users and 1 guest