SEA KNIGHT

Designs for inboard or outboard power

Moderator: BruceDow

JimmY
Posts: 596
Joined: Sat Jul 30, 2016 11:08 am
Location: Brighton, MI

Re: SEA KNIGHT

Postby JimmY » Sat Sep 16, 2017 5:44 am

Do you have a 55 gallon drum or trash can to put under it? I just know on my older Johnson that it needed it be in a larger container for the water cooling pump to work properly. Once it fires, make sure you have good water flow or shut it down.
-Jim
Nothing says poor craftsmanship like wrinkles in your duct tape!

TomB
Posts: 162
Joined: Wed Jan 18, 2017 4:07 pm
Location: Holland, MI

Re: SEA KNIGHT

Postby TomB » Sat Sep 16, 2017 6:02 am

This might not be the right time to share this, but...

images.jpg
images.jpg (11.8 KiB) Viewed 1344 times

BillW
Posts: 121
Joined: Sun Oct 05, 2008 8:03 am
Location: Seattle, WA

Re: SEA KNIGHT

Postby BillW » Tue Sep 19, 2017 5:27 pm

If the motor has not been run in a long time, I would not attempt to start it until the water pump impeller has been replaced.
When it has been unused for years, the rubber impeller vanes will have taken a "set" and probably will not provide good water pressure,
or worse yet, may have pieces of the vanes break off and become lodged in water passages in the engine block.

Also, bear in mind, never run an outboard without water. Even a few seconds running without water will destroy the impeller.

Probably, the motor will need the carbs rebuilt, and ignition tune or ignition parts replacement.

I have no experience with Bearcat motors, but the above info applies to pretty much all outboards,

Bill

Craig Aho
Posts: 404
Joined: Sat Jul 30, 2011 7:05 am
Location: Washington State

Re: SEA KNIGHT

Postby Craig Aho » Wed Sep 20, 2017 3:20 pm

Sounds like good advice and feedback Bill, Thank you.

Craig Aho
Posts: 404
Joined: Sat Jul 30, 2011 7:05 am
Location: Washington State

Re: SEA KNIGHT

Postby Craig Aho » Wed Sep 20, 2017 3:25 pm

I added the additional INterlux coats of paint on the transom and like the way it looks. I also went with FLag BLue color which is a deeper shade of blue which I also like.
Attachments
21768864_1784173838278211_6991466910443472648_o.jpg
21686772_1784173874944874_2258477718460517888_o.jpg

Craig Aho
Posts: 404
Joined: Sat Jul 30, 2011 7:05 am
Location: Washington State

Re: SEA KNIGHT

Postby Craig Aho » Thu May 17, 2018 3:47 pm

Greetings to all, I am still alive and mostly well and now with a first Grandchild so Life is full of activity. I am still trying to finish my boat which I think is about 95 percent done. I left off last year early fall with redoing the transom paint with quality Interlux Brightside paint which looks a whole lot better but I still have the rest of the hull and cabin to repaint. :( I also would love to hang my old Bearcat motor on the transom now that it is repainted so I can hook up some steering etc.but the boat is hard to access where it is located in my backyard with a heavy motor and I am not as strong as I once was. I also have some cabin interior details to do but other than that I could put her in the water. So I will try to make some progress this summer. My wife is very frustrated with me and thinks I should just get rid of it because I am never going to complete it etc. But I will continue on non the less.

Craig

joshuab
Posts: 486
Joined: Sun Apr 26, 2015 4:10 pm
Location: southern oregon coast
Contact:

Re: SEA KNIGHT

Postby joshuab » Thu May 17, 2018 8:51 pm

Your so close! Hang in there, you will be cruising it in no time. It looks beautiful by the way.
I cut twice and it's still too short :mrgreen:

User avatar
mrintense
Posts: 2733
Joined: Thu Jun 10, 2010 11:22 am
Location: Austin, Texas
Contact:

Re: SEA KNIGHT

Postby mrintense » Sat May 19, 2018 10:15 am

Hang in there Craig. Remember all the other times you encountered difficulties and got through them. You're so close now. I would personally love to see you get her in the water.
Carl
a.k.a. Clipper

Crafting a classically styled Vera Cruise named "Some Other Time"

Clipper's Vera Cruise Build

Craig Aho
Posts: 404
Joined: Sat Jul 30, 2011 7:05 am
Location: Washington State

Re: SEA KNIGHT

Postby Craig Aho » Sat May 19, 2018 4:37 pm

Thank you guys, I am trying to come up with or build a cart to haul my motor out to the boat (not so good rolling surfaces) so I can hang it on the transom which will really get me going on completion plus I will gain extra room im my small garage.

Craig

BillW
Posts: 121
Joined: Sun Oct 05, 2008 8:03 am
Location: Seattle, WA

Re: SEA KNIGHT

Postby BillW » Sat May 26, 2018 3:13 pm

Perhaps you know about this already, but the http://www.fiberglassics.com site has a forum section specifically for Bearcat outboards.

They can probably provide a lot of help. Be sure to change the water pump impeller before trying to start an outboard that has not
run for several years.

Bill

Craig Aho
Posts: 404
Joined: Sat Jul 30, 2011 7:05 am
Location: Washington State

Re: SEA KNIGHT

Postby Craig Aho » Sun May 27, 2018 7:33 pm

I use to be a member of some of these groups and there was some good feedback on these Bearcat motors but getting to meetings and getting to know some of the folks was difficult due to distance and lack of time to attend so getting any real one on one help wasn't possible.


Return to “Power Boats”

Who is online

Users browsing this forum: No registered users and 8 guests