Glen-L.com

The Boatbuilder Connection
It is currently Sat May 25, 2013 3:43 pm

View unanswered posts | View active topics


Board index » Design » Power Boats

All times are UTC - 8 hours [ DST ]



Post new topic Reply to topic  Page 3 of 3
  [ 40 posts ]  Go to page Previous  1, 2, 3
  Print view Previous topic | Next topic 
Author Message
thinwater
PostPosted: Sat Jan 14, 2012 6:43 pm 
Offline

Joined: Mon Oct 27, 2008 5:15 am
Posts: 48
Well it should be water worthy now that its externally sealed. Now to UV protect the Black Cherry Trim work, then prime and paint the ply. Hopefully while my little brother Urethanes the trim I'll get the inside ready to do.


Attachments:
File comment: Externally sealed
2012_01-14_08.JPG
2012_01-14_08.JPG [ 2.57 MiB | Viewed 545 times ]
Top
 Profile  
 
thinwater
PostPosted: Mon Jan 30, 2012 8:39 am 
Offline

Joined: Mon Oct 27, 2008 5:15 am
Posts: 48
Pretty in Primer

Image
Top
 Profile  
 
upspirate
PostPosted: Mon Jan 30, 2012 12:25 pm 
Offline
User avatar

Joined: Fri Dec 08, 2006 5:21 pm
Posts: 8007
Location: tarpon springs fl
I like the painted with varnished trim look

_________________
Boat building can best be defined as an endless series of
tragedies obscured by the occasional miracle, followed by a good bottle of beer.

Don't Dream Your Life, Live Your Dream
Top
 Profile  
 
thinwater
PostPosted: Sun Feb 05, 2012 5:21 pm 
Offline

Joined: Mon Oct 27, 2008 5:15 am
Posts: 48
Pretty close, the white is still primer. Blue is one covering coat after a tack coat just to see where I'm at. Where I found I'm at is, feather the tape lines down, re-tape about a 16th off the old tape line and put a finish coat on it. I'm satisfied with the finish of the blue area (many times primed and wet blocked), and I'm going to semi gloss flatten the off white portion, which is showing in white primer in these shots. Interlux Brightside, primer, sapphire blue, and the trim is black cherry unstained just varnished with Helmsman UV protectant urethane.

Image
Image
Image
Thanks again for all of your inspiration. The support of the forumn, and "The Gathering 2009" are mostly responsible for this happening.
Top
 Profile  
 
thinwater
PostPosted: Fri Mar 02, 2012 7:21 am 
Offline

Joined: Mon Oct 27, 2008 5:15 am
Posts: 48
Working on filleting and sealing the inside.


Attachments:
2012_02-21_10.JPG
2012_02-21_10.JPG [ 284.68 KiB | Viewed 413 times ]
2012_02-21_09.JPG
2012_02-21_09.JPG [ 435.85 KiB | Viewed 413 times ]
2012_02-21_08.JPG
2012_02-21_08.JPG [ 359.81 KiB | Viewed 413 times ]
Top
 Profile  
 
thinwater
PostPosted: Thu Mar 29, 2012 6:53 pm 
Offline

Joined: Mon Oct 27, 2008 5:15 am
Posts: 48
Weighed in at 760 lbs bare hull, she should float and run shallow as intended with the 22' length and almost 6' beam! Woo hoo!


Attachments:
File comment: Little more support under the front of the trailer and I can splash it!
2012_03-29_07).JPG
2012_03-29_07).JPG [ 2.66 MiB | Viewed 356 times ]
Top
 Profile  
 
upspirate
PostPosted: Thu Mar 29, 2012 7:04 pm 
Offline
User avatar

Joined: Fri Dec 08, 2006 5:21 pm
Posts: 8007
Location: tarpon springs fl
Looks close to splashing if you haven't....looks great!

Post in Launching ramp topic when you do!! :D

_________________
Boat building can best be defined as an endless series of
tragedies obscured by the occasional miracle, followed by a good bottle of beer.

Don't Dream Your Life, Live Your Dream
Top
 Profile  
 
thinwater
PostPosted: Wed Apr 04, 2012 7:16 am 
Offline

Joined: Mon Oct 27, 2008 5:15 am
Posts: 48
Did a leak test and checked that off. Powered up the river a little with the 6hp johnson trolling motor, draft was about 2.25" I believe that 10hp would've planned the boat out. I really liked it. Now to get the main power working and mount that trolling motor and get juice to it.
Top
 Profile  
 
thinwater
PostPosted: Tue May 22, 2012 7:10 pm 
Offline

Joined: Mon Oct 27, 2008 5:15 am
Posts: 48
http://www.youtube.com/watch?v=GrgVhnJSad8&feature=share

Got the jet drive running will post in maiden voyage or launch if I can find it.
Top
 Profile  
 
vettepilot
PostPosted: Tue May 22, 2012 9:13 pm 
Offline
User avatar

Joined: Wed Jan 26, 2011 12:40 am
Posts: 234
Location: Childers SE Queensland
thinwater wrote:
Did a leak test and checked that off. Powered up the river a little with the 6hp johnson trolling motor, draft was about 2.25" I believe that 10hp would've planned the boat out. I really liked it. Now to get the main power working and mount that trolling motor and get juice to it.


2.25" WOW thats incredible :shock: ...the places you will be able to go :wink: Great Looking Boat.. Well Done!

_________________
The Bitterness of Poor Quality, Remains Long After The Sweetness of Cut Price is Forgotten...Thanks Dad R.I.P.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 3 of 3
  [ 40 posts ]  Go to page Previous  1, 2, 3

Board index » Design » Power Boats

All times are UTC - 8 hours [ DST ]

Who is online

Users browsing this forum: Exabot [Bot], jbooher, svenole and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group