modified malahini

Designs for inboard or outboard power

Moderator: BruceDow

Post Reply
Ranny
Posts: 79
Joined: Wed Jun 25, 2014 3:01 pm
Location: Heritage Hunt, VA

Re: modified malahini

Post by Ranny »

Anybody ever used the Festool sanders with dust control? I have used mine inside on drywall virtually no dust.
Ranny

User avatar
BayouBengal
Posts: 1106
Joined: Tue Jul 31, 2007 7:29 am
Location: Baton Rouge, Louisiana

Re: modified malahini

Post by BayouBengal »

I started off the sanding of my planks with a buffer/polisher from Harbor Freight with a very soft 7" foam pad that I glued velcro strips in order to attach the large 60 grit sanding discs. You want to keep the disc as flat as possible against the wood, but when it gets away from you the soft foam helps you avoid digging into your wood. Quite a dust storm was created, but I was able to get all the planks fairly even with each other in about a day. From here, went to the long board with 80 grit paper.

Brandlin
Posts: 29
Joined: Thu Jul 21, 2016 6:22 am
Location: Nr Chester UK / N Wales Coast

Re: modified malahini

Post by Brandlin »

Ranny wrote:Anybody ever used the Festool sanders with dust control? I have used mine inside on drywall virtually no dust.
If I could afford festool products, then I could afford to buy a boat not build one!

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

Finished veneering the sides. I still have to do the transom.
IMG_4308[1].JPG
Found two problem areas. I think I know what I want to do, but seeking input.
IMG_4304[1].JPG
IMG_4305[1].JPG
This area has one board that must have been a little thinner. If I sand area to get it smooth, the side will have a dip in it. I plan on cutting this area out and adding a dutchman. Worried I might screw everything up. My other choice is the sand boards, but leave height difference and fill with epoxy to get smooth. Will this be noticeable?
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

Second area is near the transom. I sanded one area too flat and have lost the smooth curve of the tumble home.
IMG_4306[1].JPG
My thought is to also do a dutchman in this area, or am I being too fussy and this will not be an issue?
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

User avatar
Roberta
Posts: 6630
Joined: Tue Jul 31, 2007 5:23 pm
Location: East Troy, Wisconsin

Re: modified malahini

Post by Roberta »

Looking Good!!! Some Famowood filler will take care of the small gaps. Then a good filler stain like Interlux or Sandusky will help smooth out color variation. As for the flattening out, can you take some off on the upper boards (now lower) to bring back the contour? Transom bands will also cover some if it does not go too far forward. Stern side bumpers may also hide the change in contour. Not really that bad, though.

Roberta :D
Roberta "Queen of the Boat Builders"
Built Zip "Oliver IV", Super Spartan "Jimmy 70", and Torpedo "The Glen L".

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

Tahnks Roberta! The error at the transom could be filled with famowood and reshaped. I am planning on using transom bands and that will cover the area. Luckily it does not go too far forward. I think the side board will have to be dutchmanned unfortunately :x
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

User avatar
vupilot
Posts: 3531
Joined: Wed Apr 15, 2009 7:36 am
Location: Indy
Contact:

Re: modified malahini

Post by vupilot »

Dont use fillers to fix the unfair or flat portion if you plan on keeping the hull bright finish, it will show. But a little careful sanding to help round it again and once transom bands go on youll definitely be the only one to ever notice.

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

I fixed the depressed area on the starboard side yesterday. First I marked the area to be cut out.
IMG_4309[1].JPG
Next I selected a board with similar grain. (Didn't really have much left to choose from)
IMG_4310[1].JPG
I marked the depth of cut on my saw.
IMG_4311[1].JPG
And cut the border of the area to be removed.
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

I used a chisel to remove the board (probably could have done it faster with my router, but afraid with one slip could have made a big scar)
IMG_4315[1].JPG
Next I fit the new piece and epoxied in place.
IMG_4316[1].JPG
IMG_4317[1].JPG
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

Today, I sanded area.
IMG_4319[1].JPG
IMG_4318[1].JPG
I think it came out fairly good. It still needs more sanding, but I still have to sand the entire side. I hope staining will hide it better.
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

User avatar
rbrandenstein
Posts: 841
Joined: Mon Mar 08, 2010 3:51 pm
Location: O'Fallon, MO

Re: modified malahini

Post by rbrandenstein »

Nice dutchman! Staining will help a lot to make the look consistent.

However, you will always see it, but the rest of us will not. :D
________________
Bob
Completed Malahini (launched 6/24/2012)
http://bobsboatbuild.blogspot.com/

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

I am so sick of sanding. That's all I've been doing for the past several weeks. So, no pictures to post. Maybe I'm being to picky with the finish. Also, Lisa has been demanding a lot of my weekend time. It's hard to make any progress when you only have an hour on the weekend to work on the boat. Alas, I'm afraid I am not going to make my stated plan to flip the Mona Lisa Thanksgiving weekend.
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

User avatar
vupilot
Posts: 3531
Joined: Wed Apr 15, 2009 7:36 am
Location: Indy
Contact:

Re: modified malahini

Post by vupilot »

We do tend to sand the bottom and try to get a perfect paint job but then flip it only to realize youll only ever see a few inches of paint on the sides, transom and under the bow. Once it's fair and smooth its time to fiberglass while the temps are perfect for it before it gets too cold.
However, on the sides its certainly worth taking your time, you would hate to have sanding scratches show up under the fiberglass and varnish where you could have spent more time sanding. I liked to wet with water or mineral spirits to help show any scratches. I went from 120 up to 320 grits before fiberglass and paint/varnish, mostly using a ro sander but final passes by hand.

User avatar
DrBryanJ
Posts: 1175
Joined: Fri Jul 22, 2011 6:05 am
Location: Pompton Plains, NJ

Re: modified malahini

Post by DrBryanJ »

I'm not spending alot of time on the bottom, but I'm on the transom and sides. I started with 60 grit on an ro sander and a long board. Also using a cabinet scraper and a card scraper. Planing on going to 220 grit. Should I go higher before epoxy?
Bryan

Building a malahini "Mona Lisa"

My wife said "If I build a boat, she's getting a divorce."
We're still happily married, but now she just wants "the dam boat out of the garage."

Post Reply

Return to “Power Boats”