Aussie Gentry

Designs for inboard or outboard power

Moderator: BruceDow

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Fri Sep 30, 2016 4:09 pm

G/Day well fitted a plastic water pipe into the shaft hole using Bote-Cote epoxy makes for a neat and waterproof fixture......John
IMG_6697.jpg

IMG_6696.jpg

IMG_6690.jpg

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sun Oct 02, 2016 3:14 pm

G/Day well got stuck into a sheet of 316 Stainless and used a plasma cutter for the first time i bought this thing 5 years ago, it worked very well so here is what i did ....John
IMG_6708.jpg

IMG_6702.jpg

IMG_6700.jpg

User avatar
Roberta
Posts: 5946
Joined: Tue Jul 31, 2007 5:23 pm
Location: East Troy, Wisconsin

Re: Aussie Gentry

Postby Roberta » Sun Oct 02, 2016 3:51 pm

Looking great. Are you going to Tig weld the cutwater?

Roberta :D
Roberta "Queen of the Boat Builders"
Built Zip "Oliver IV", Super Spartan "Jimmy 70", and Torpedo "The Glen L".

User avatar
jenko
Posts: 815
Joined: Sat Mar 19, 2011 2:50 am
Location: Pine Mountain . Vic . Australia
Contact:

Re: Aussie Gentry

Postby jenko » Sun Oct 02, 2016 5:25 pm

John when I did my cutwater ,welding the two halves together caused the whole thing to shrink along the seam weld ( I used a tig) which in turn meant I needed to cut a few slits in either side and reweld to get it to fit .
the warpage was as bad as when the top was snug fit the bottom didn't mate up by 50 mm

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Mon Oct 03, 2016 11:51 pm

G/Day Roberta / Jenko yes i will tack weld on the boat fires then make some outside molds and screw on to the molds then tig weld the inside, then make some internal molds and screw the cutwater to them and tig weld the outside this process should stop any distortion ...watch this space :lol:

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Oct 15, 2016 2:52 pm

G/Day well weather is great in Oz now so i got 2 coats of epoxy primer on the transom (Bote-Cote) and also a flow coat stain on the sides now i will see what i am sanding .....John
IMG_6765.jpg

IMG_6763.jpg

IMG_6760.jpg

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Oct 15, 2016 8:20 pm

G/Day well sanded off the guide cote looked good and felt good, so the first primer coat of epoxy went on .....John
IMG_6766.jpg

IMG_6764.jpg

IMG_6768.jpg

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Oct 15, 2016 8:21 pm

IMG_6773.jpg

IMG_6771.jpg

IMG_6775.jpg

User avatar
Roberta
Posts: 5946
Joined: Tue Jul 31, 2007 5:23 pm
Location: East Troy, Wisconsin

Re: Aussie Gentry

Postby Roberta » Sun Oct 16, 2016 5:48 am

NNNIIIICCCCEEEEE!!!!

Roberta :D :D :D :D :D :D :D
Roberta "Queen of the Boat Builders"
Built Zip "Oliver IV", Super Spartan "Jimmy 70", and Torpedo "The Glen L".

ian bell
Posts: 147
Joined: Thu Sep 26, 2013 8:47 am
Location: Chambers Flat 4133 Qld
Contact:

Re: Aussie Gentry

Postby ian bell » Sun Oct 16, 2016 1:28 pm

Hi John .Great work ,love the finish.
Ian

User avatar
Bill Edmundson
Posts: 10449
Joined: Wed Nov 23, 2005 6:45 am
Location: Birmingham, AL, USA
Contact:

Re: Aussie Gentry

Postby Bill Edmundson » Sun Oct 16, 2016 2:11 pm

Looks great! But, sanding it will be heart breaking, until the clear-coat goes on!

Bill
Mini -Tug, KH Tahoe 19 & Bartender 24 - There can be no miracle recoveries without first screwing up.
Tahoe 19 Build

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Tue Oct 18, 2016 9:49 pm

G/Day all and thanks yes Bill i am lubing the elbows now :D got the second primer coat on now to do this all again on the other side, most of the grain has filled so maybe only 6 coats of finishing clear ?????......John
IMG_6778.jpg

IMG_6777.jpg

IMG_6779.jpg

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Thu Oct 20, 2016 5:17 pm

G/Day well second coat of epoxy primer on now to prepare to glass the bottom and make the trailer runners ....John
IMG_6782.jpg

IMG_6781.jpg

IMG_6785.jpg

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Dec 10, 2016 3:17 pm

G/Day well i have 5 coats of epoxy primer on both sides, i was thinking during the night that how am i going to get into this boat if i am not at a wharf / jetty and it has no cav plate to step on to, so i made a solid Mahogany step bumper and side trims took a bit to fit the rear peice will be held by epoxy and 5 off 3/8" S.S long bolts through the transom
IMG_6881.jpg

IMG_6878.jpg

IMG_6882.jpg

John R
Posts: 116
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Dec 10, 2016 3:18 pm

IMG_6895.jpg

IMG_6883.jpg


Return to “Power Boats”

Who is online

Users browsing this forum: Bing [Bot] and 13 guests