Aussie Gentry

Designs for inboard or outboard power

Moderator: BruceDow

rleete
Posts: 128
Joined: Sun Sep 18, 2016 9:22 am
Location: Rochester, NY

Re: Aussie Gentry

Postby rleete » Sat Dec 10, 2016 7:42 pm

Looks good. Nice how the side trim leads right into it. Makes it look more integrated and less just tacked on.

User avatar
speedracer
Posts: 139
Joined: Sun Jan 16, 2011 8:48 pm
Location: Covingtion, Louisiana

Re: Aussie Gentry

Postby speedracer » Sun Dec 11, 2016 7:44 pm

John - Your build is looking great. I had the same concern about getting in my Monaco from the water. How wide did you make that step at the stern? Also, how far above the bottom did you place it?
Great spirits have always encountered violent opposition from mediocre minds. Albert Einstien

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sun Dec 11, 2016 11:31 pm

G/Day Speedracer thanks for that ok i made it 200mm down from the bottom center and 170 out from that point i have a total of 5 by 3/8" S.S. threaded rods picking up solid timber inside the transom and the outer 2 from the center pick up brackets at the engine bearers, also epoxy the bumper / step to the transom hope this helps ......John

User avatar
speedracer
Posts: 139
Joined: Sun Jan 16, 2011 8:48 pm
Location: Covingtion, Louisiana

Re: Aussie Gentry

Postby speedracer » Mon Dec 12, 2016 5:45 am

Yes, that's what I needed. I am thinking of something similar. Thanks.
Great spirits have always encountered violent opposition from mediocre minds. Albert Einstien

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Tue Dec 27, 2016 3:13 pm

G/Day well got the edges done in 6oz glass using Bote-Cote epoxy resin and for the first time using peel ply as well my first attempt was pretty good better than 80% my second was neary 100% and the finish is so smooth, i will do the stem next and then the compete bottom now that all the hard bits are done and also i have a handle on the peel ply ......John
IMG_6930.jpg

IMG_6927.jpg

IMG_6929.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Tue Dec 27, 2016 3:14 pm

IMG_6937.jpg

IMG_6932.jpg

IMG_6933.jpg

User avatar
jenko
Posts: 796
Joined: Sat Mar 19, 2011 2:50 am
Location: Pine Mountain . Vic . Australia
Contact:

Re: Aussie Gentry

Postby jenko » Tue Dec 27, 2016 3:55 pm

looks good John ,I contemplated using peel ply now I wish I had

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Jan 14, 2017 3:49 pm

G/Day well we got the glass down on the bottom yesterday weather was great and got the peel ply on as well here are some photos ........John
IMG_6977.jpg

IMG_6973.jpg

IMG_6983.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Wed Feb 15, 2017 10:24 pm

well the boat is now ready to prime and paint to the water line the finish after taking the peel ply of was great took 2 hours to sand smooth and get another 2 coats of epoxy primer on, then sanded back total sanding time 4.2 hours.....John
IMG_6985.jpg

IMG_6984.jpg

IMG_6987.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Feb 18, 2017 6:41 pm

G/Day well steering wheel is cleared and finished also the bottom has been sanded and finished and cut tape on 2" below the waterline mark this 2" section will be gold so tomorrow i will get the Luxapoxy primer on ......John
IMG_7012.jpg

IMG_7011.jpg

IMG_7013.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Sat Feb 18, 2017 6:42 pm

IMG_7016.jpg

IMG_7014.jpg

IMG_7018.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Fri Feb 24, 2017 7:01 pm

G/Day well bit more done made the dash board it is Mahogany and Silver Ash trim .....John
IMG_7026.jpg

IMG_7025.jpg

IMG_7031.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Fri Feb 24, 2017 7:05 pm

G/Day well nice warm weather so i got 4 coats of primer on this is Luxepoxy white primer now wait the 7 day for full cure then sand ready for the Luxathane Blue......John
IMG_7040.jpg

IMG_7041.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Mon Mar 13, 2017 5:55 pm

G/Day well i have rolled 4 coats of Luxathane (water raceway blue) wait till hard then sand and fair then i will spray the last 2 coats, also finished the dash and fitted the steering wheel......John
IMG_7088.jpg

IMG_7081.jpg


IMG_7083.jpg

John R
Posts: 115
Joined: Wed Feb 11, 2015 3:04 pm

Re: Aussie Gentry

Postby John R » Mon Mar 13, 2017 5:57 pm

IMG_7089.jpg

IMG_7085.jpg

IMG_7086.jpg


Return to “Power Boats”

Who is online

Users browsing this forum: Bing [Bot] and 19 guests