Clinker Planking


Once the shell of planking is assembled, transverse sticks of oak or elm, called timbers, are steam-bent to fit the internal concave side. The timbers are frequently miscalled ribs. Elm species are not durable where the boat is used frequently in fresh water. As the timbers are bent in, they are copper riveted to the shell, through the lands of the planking. With the timbers all fitted, longitudinal members are bent in. The thwart risings are fastened through the timbers with its upper edge on the level of the undersides of the thwarts. Bilge keels are added to the outside of the land on which the boat would lie on a hard to stiffen it and protect it from wear. A stringer is usually fitted round the inside of each bilge to strengthen it. In a small boat, this is usually arranged to serve also as a means of retaining the bottom boards. These are removable assemblies, shaped to lie over the bottom timbers and be walked upon. They spread the stresses from the crew's weight across the bottom structure.


Inboard of the sheer strake the heavier gunwale is similarly bent in along the line of the sheer. This part of the work is finished by fitting the breast hook and quarter knees. Swivel or crutch chocks are fitted as appropriate to the gunwale, the thwarts fitted down onto the rising and held in position by knees up to the gunwale and perhaps down onto the stringer. The structure of gunwale, rising, thwart and thwart knees greatly stiffens and strengthens the shell and turns it into a boat. There are several ways of fixing the rubbing strake but in a clinker boat, it is applied to the outside of the sheer strake.


Finally, the fittings such as swivels or crutch plate, painter ring, stretchers, keel and stem band are fitted and fixed with screws. In a sailing dinghy, there would be more fittings such as fairleads, horse, shroud plates, mast step, toe straps and so on.


That more or less finishes the boatbuilder's work but the painter has yet to varnish or paint it. At stages along the way, he will have been called in to prime the timber. This is particularly so immediately before the timbering is done. The boatbuilder will clean up the inside of the planking and the painter will prime it and probably more, partly because it is easier that way and partly so as to put some preservative on the planking behind the timbers. Similarly, it is best to have the varnishing done after the fittings are fitted but before they are shipped. Thus, the keel band will be shaped and drilled and the screw holes drilled in the wood of keel and stem then the band will be put aside while the varnishing is done.


The planks may be fastened together in several ways:

  • with copper rivets consisting of a square nail and a dish shaped washer called a rove. The land is pierced, the nail knocked through from the outside, the rove punched on while the head is held up by a dolly. The nail is cut off just proud of the rove and the cut end clenched over the rove while the dolly (a small portable anvil, usually of cylindrical shape) is used to hold the nail in place. In planking up clinker work, one man can hold both dolly and clenching hammer.
  • with iron nails with the pointed nail ends protruding on the inside of the boat, bent over and back into the wood in the form of a hook. This is a cheap and cheerful technique maybe called clinching in some parts but usually, in England at least, "turnin'-em-over". It is the sort of thing which used to be found in Scandinavian-built boats but even with iron nails on the lands, they were usually properly clenched over roves. Nails fastening timbers were sometimes turned over, particularly where removable bottom boards were to rest on the timbers. However, it was possible to tread the bottom boards onto the clenched nails and where marks were left, gouge out recesses to accommodate the clenched nails.
  • screws were used for fixing the ends of the strakes to apron and transom and in later times, knees to gunwale and thwarts, but traditionally, this last would be done with a clench bolt or a large copper nail, clenched.
  • adhesive, notably epoxy. Traditionally, lands were neither glued nor was anything used to bed them. The garboard was bedded onto the hog and keel, and the ends of the strakes onto the stem and apron using a mixture of white lead and grease. During the World Wars new techniques and materials were developed by the aircraft industry. By the mid 1950's, these were well infiltrated into the boatbuilding trade. New boats in classes of racing dinghy with clinker hulls were built as glued clinker boats. The basic construction was the same but ply planking was used and the lands were glued with no fastenings, except that the ends and garboards were still screwed to apron and hog. The need to prevent the splitting of the planks was removed by the use of ply so no timbers were used. Except for a light gunwale and wide rubbing strake, the longitudinals were omitted too. A short thwart rising and knees were glued to the planking. These boats were all decked and that is how adequate stiffness was achieved. So that the liquid glue could be laid onto the land before the next plank was assembled onto it, they were built upside down.

Fastening the center-line structure

In the last few years of wooden boat construction, glue and screws took over, but until the 1950s, the keel, hog, stem, apron, deadwoods, sternpost, and perhaps transom would be fastened together by bolts set in white lead and grease. There are three kinds of bolts, of which, nowadays, the screw bolt, with its nut and washer, is by far the most common. The second type of bolt is the pin bolt or cotter bolt, which, instead of a thread, has a tapered hole forged through the end away from the head into which a tapered pin or cotter is knocked. The taper is in effect a straight thread. In conjunction with a washer, this draws the bolt tight, as a nut does on a screw bolt. The third type of bolt is the clench bolt. It has some of the features of a rivet but was usually much longer than the normal rivet, in a wooden ship, perhaps a meter or more. For a shipwright's use, it is of copper. A head is formed by clenching it over a washer in a swage plate. It is then knocked through a hole bored through the work to be fastened. The head is held up with a dolly and the other end is formed in the same way as the head but without the swage plate. Until well into the nineteenth century, this is what held the great ships of the world together, though some may have used iron. Until the late 1950s, the centre-line assembly of British Admiralty twenty-five foot motor cutters were fastened this way.

Where suitable metal was not available, it was possible to use treenails (pronounced trennels). They were like clench bolts but made of wood, and instead of being clenched, they had a hardwood wedge knocked into each end to spread it. The surplus was then sawn off.

Relationship between clinker and carvel

The Clinker form of construction is linked in people's minds with the Vikings who used this method to build their famous longships from riven timber (split wood) planks. Clinker is the British term, it is known as lapstrake in North America. In general, the languages of other countries where the method was current use some version of the word clinker.

Carvel construction was probably invented earlier than clinker but in other parts of the world. In Europe carvel was the method of the south probably having spread though the Mediterranean from the Middle East. Clinker was the method of north Europe having developed apparently, in the Baltic.

The smoother surface of a carvel boat gives the impression at first sight that it is hydrodynamically more efficient. The lands of the planking are not there to disturb the stream line. This distribution of relative efficiency between the two forms of construction is an illusion because for given strength, the clinker boat is lighter. It therefore displaces less water so it has less to push aside while moving. The reduced displacement could be used to make the lines finer so as to make the passage through the water easier still. Of course, displacement was increased as cargo was loaded, but still the clinker vessel had the advantage in efficiency as the structure was less bulky. Therefore, for a given internal volume there was a smaller external one. That means that a bulkier cargo could be carried if need be.