Rollers or Bunks for Flats Flyer

Boat trailers and trailering

Moderator: ttownshaw

Post Reply
User avatar
Conrad
Posts: 147
Joined: Thu Feb 11, 2016 10:17 am
Location: Kathleen GA

Rollers or Bunks for Flats Flyer

Post by Conrad »

I purchased a used trailer with large rollers on it. It had a 21 foot 92 bay liner but it will be modified to a 20' Flats Flyer... I'm trying to decide: Rollers or bunks? Or combination?
Attachments
20181002_081235.jpg
Keep your lines tight!

Conrad

Consider what God has done: Who can straighten what he has made crooked? Ecc 7:13 :)

User avatar
Bill Edmundson
Posts: 12156
Joined: Wed Nov 23, 2005 6:45 am
Location: Birmingham, AL, USA
Contact:

Re: Rollers or Bunks for Flats Flyer

Post by Bill Edmundson »

Bunks

Too many parts on rollers! It's too easy to miss one going bad. Then you end up with a big gouge in your hull. And rollers tend to dent the hull.

Bill
Mini -Tug, KH Tahoe 19 & Bartender 24 - There can be no miracle recoveries without first screwing up.
Tahoe 19 Build

User avatar
Conrad
Posts: 147
Joined: Thu Feb 11, 2016 10:17 am
Location: Kathleen GA

Re: Rollers or Bunks for Flats Flyer

Post by Conrad »

After that, composite or wood? Anyone try both? The obvious goal would be not to replace the wood boards
Keep your lines tight!

Conrad

Consider what God has done: Who can straighten what he has made crooked? Ecc 7:13 :)

User avatar
kens
Posts: 5272
Joined: Wed Nov 12, 2003 5:25 pm
Location: Coastal Georgia

Re: Rollers or Bunks for Flats Flyer

Post by kens »

I had a roller trailer once, and never again.
Well, rollers up front on the winch stand I use well,
But rollers on the main hull and aft, no.
Oak..........the juice ain't worth the squeeze :D :shock: :o :)

hoodman
Posts: 2760
Joined: Thu Nov 10, 2011 8:48 am
Location: Lafayette, IN

Re: Rollers or Bunks for Flats Flyer

Post by hoodman »

Pressure treated 2x material is fine. I'm not sure composite lumber would be stiff enough.
Matt

Building a Geronimo......!
viewtopic.php?f=2&t=25139

TAB
Posts: 191
Joined: Tue Aug 09, 2016 3:22 pm
Location: OR

Re: Rollers or Bunks for Flats Flyer

Post by TAB »

Conrad wrote:After that, composite or wood? Anyone try both? The obvious goal would be not to replace the wood boards
composite will not work, it is way too flexible. most of them recommend joists at 12" on center, where standard is 16" a few even require it.

either pt or red wood. fyi, do not use galvanized hard ware on modern pt. it will not last. either use ss( which is really not that much) or use nylon isolators. been more then a few lawsuits in the last few years over it, in the deck building industry. the coated stuff is fine, but honestly you can order ss hardware for very little off line.

User avatar
Jimbob
Posts: 876
Joined: Thu Jul 25, 2013 1:07 pm
Location: Sacramento, CA

Re: Rollers or Bunks for Flats Flyer

Post by Jimbob »

Re: material to use for bunks
I called the people that built my custom trailer (sport boat trailers) and asked them what they used for their bunks. They told me that they use douglas fir. The douglas fir conforms to the boat better. They also said don't use hardwood. In additon, they said that treated wood becomes brittle over time, and don't recommend it.
Hope this helps.
Jim
Jim Neeley
Building a Barrelback in Sacramento, CA
viewtopic.php?f=15&t=28089#p172969

User avatar
Conrad
Posts: 147
Joined: Thu Feb 11, 2016 10:17 am
Location: Kathleen GA

Re: Rollers or Bunks for Flats Flyer

Post by Conrad »

Thanks everyone!
Keep your lines tight!

Conrad

Consider what God has done: Who can straighten what he has made crooked? Ecc 7:13 :)

Post Reply

Return to “Trailers and trailering”